if you remove the waste box on the right side is a gear. in french ! The cable connection may get loose because of tranport. On OKI C5800, poen the right handside of printer cover and you find it there. http://vbview.net/oki-error/oki-error-fatal-928.php
by Lakespyder on Jul 17, 2008 at 5:46am Add comment Please sign in to comment 0 Lakespyder,thanks a lot for the information! Summary:Printer has displayed a "Fatal Error" message. by bumpi on Apr 1, 2005 at 8:01am Add comment Please sign in to comment 0 ERROR ENGINE on a OL400. Thank you for everything - Anonymous I could use the codes for a C5800.Thanks - Anonymous Hello , how cand I can get rid of the Toner Empty Code for OKI https://community.spiceworks.com/how_to/14305-fixing-fatal-error-code-929-on-okidata-printers
how can i fix it by unknown on Apr 28, 2010 at 8:49am Add comment Please sign in to comment 0 This works - keep track of what you are doing.... by moe on Apr 25, 2002 at 2:40pm Add comment Please sign in to comment 0 I keep getting a "ERROR ENGINE" on my okilaser 400.any help ??? Always try to update your anti-virus considering that virus sometimes causes this error. Bueller? - mrmunroe 0 What next?Have OKI c5500 Finally fixed paper jam error, then had Fatal Error 928.
It can be a messy job if you've never done it before.In my opinion it's worth learning how to do it because if there's no scratches, dents or rips in the The display will read SOS1, SOS2, with the cursor at SOS1. If the problem still persists, you must replace the engine controller circuit board. Zero cost and still using the same fuser unit.
I've reset the printer and when I do, it warms up, multiple times-adjusting colour, etc. After you get the wires in the 2 holes, check for continuity from the end of the wires and the terminals if you can. Error 173 on the 9300 has to do with the fuser. The remaining paper in the printer is not visible, whether I open the back door or the top.
by Lakespyder on Jul 15, 2008 at 2:12pm Add comment Please sign in to comment 0 The info I found for error 929 says that it is a Waste Toner Transfer by seth_zuno on Oct 29, 2008 at 10:54am Add comment Please sign in to comment The magenta toner is not locked in property. Basically means there is a fan that is not working of is no longer plugged into the Hv Board - Anonymous 2 I have tried removing and reseating the ROM chip, If a device is the cause of the issue, you could fix the problem by disconnecting it.
Our help desk guy did a little research and thought that the drum needed to be replaced. Level 2 Expert 269 Answers Are you an OKI Printer and Copier Expert? French Site L'imprimante en question Friends Archaeology news Labels Brother (7) Brother DCP (6) Brother HL (1) Brother MFC (7) Cano IR (1) Cano S (1) canon (29) Canon BJC (2) Love the c5800 printer but am disgusted with the engineering put into forcing owners to frequently replace perfectly good parts.
The result of this error usually causes the virtual memory to run slow. You simply have to put that cable on its correct position. I'm not if the drum may be sitting a little to low which is causing it to touch the belt. You can add, delete list items and change the quantity of spare parts.
The error codes can range from 140, 141, & 142. So, you should reboot the machine as well as taking out the toner waste bottle and vacuuming out the waste toner duct and box. anyone have a solution for me without going to go out and buy a new printer or break this okidata printer ...it would be awesome! Source Reseat the Contact Sensor Spring assembly and inspect it for damage or mis-alignment.
The problem is the screw and nut that hold the thermistor in place is locktite. Any help, advice or insight will be greatly appreciated!Thanx, Rodd by unknown on Nov 29, 2006 at 9:22am Add comment Please sign in to comment 2 I have OKI C9600Please tell May be if ynlucky, you have to change this card.Best of luck.
Here we will give you some highlight of the most common errors of computers as well as the solutions that you can take to get rid of them. What's the best way to do this? © Copyright 2006-2016 Spiceworks Inc. Did not help.Replaced Fuser & still has Fatal Error.Any suggestions as to what to do next?Thanks"I had the same situation. Only possibility to print again, is to plug it off and on...
Reseat the Image Drums. Restart the unit by unplugging it and hopefully it will be ok. Expand Popular Questions 6 Answers OKi C5800ldn 231: fatal error 03 OKI C5800Ldn Led Printer 6 Answers Service Call: 173: Fatal Error OKI C5150n Led Printer 1 Answer '928 Fatal Error http://vbview.net/oki-error/oki-error-142-fatal-error.php If the error was still there when you powered up without the RAM and HDD your problem is the CU PCB and it will need to be replaced.Hope that helps you.
MVP: An expert that got 5 achievements. Twist the two wires together and power up the machine. Anyone know what it means? Suess simple.
Can someone help me out please?Thanks. Next morning, we realized we'd made a mistake when everyone's keyboards failed to work. Manuals Attwood Manuals Yamaha Manuals Lowrance Electronics Manuals Raymarine Manuals O'Brien Manuals Show All > Top Musical Instrument Device Types Microphone Manuals Musical Instrument Manuals Electronic Keyboard Manuals DJ Equipment System by unknown on Dec 1, 2011 at 3:22am Add comment Please sign in to comment 0 I have an Oki data b4600, it ran well for a year with my passport
Who knows what the tech's time would have cost. All counter info is written to an eeprom flash chip on the mainboard, and cannot be turned back otherwise. Replace fuser or if no-go, Main board. Actually I've learned they're not fuses, they are thermistors.
worth looking into, try calling the oki support centre in your country.PS, thanks for replying to my post, however, there is no 'refresh' button. - unknown 0 Incorrect, only way to by unknown on Feb 26, 2013 at 12:07pm Add comment Please sign in to comment 0 have problem with oki c5900..POWER ON/OFF203:FATAL ERROR fffffc9,1) c3 (ffffffc9,1) c4 c5 (fffffcb,1) c5 by Thanks again! Could there be another problem besides the board.